WHEN YOUR WATER HEATER FAILS: IMMEDIATE RESPONSE GUIDE

When Your Water Heater Fails: Immediate Response Guide

When Your Water Heater Fails: Immediate Response Guide

Blog Article

Go Deal Now

The article author is making a few great points on the subject of What Would Cause My Electric Water Heater to Stop Working? in general in this article following next.


How to Troubleshoot and Repair an Electric Water Heater
Lots of modern homes take advantage of an electric water heater for their heating unit, because of its ease and also convenience of use. Nevertheless, just like any other electric devices, problems might occur with its use, all of a sudden. It can be really discouraging to awaken to a cool shower rather than a warm one or having your bath with water that isn't warm adequate or even also hot. Whatever the instance may be, hot water heater problems can be rather nerve-racking. Luckily, we have actually made a list of possible services to your hot water heater concerns. There are a variety of factors that could trigger a lot of these problems, maybe a problem with the power supply, the electrical heating element, or the thermostat. Prior to doing anything, ensure you switch off the major power supply for safety and security. Whatever the problem is, getting it fixed need to not present way too much of a problem if you adhere to these steps:

Examine Your Power Supply:


As basic as this may seem, it is really essential. Without ample power, your water heater will certainly not operate. So the first thing to do when your water unexpectedly retires is to validate that it isn't a power problem. Examine if the fuse is blown out or the breaker tripped. If the circuit breaker is the concern, merely transform it on and off again. Replace any damaged or worn-out fuse. Examine the device with power after these modifications to see if it's currently working.

Inspect the Heating Element in the Hot Water Heater:


If it's not a power issue, then try looking into your heating element if it is still working. Examine each of your heating elements to be sure the issue isn't with any one of them. If any of them is damaged, change that part and after that check whether the hot water is back on.

Examine Your Thermostat:


If your hot water heater still isn't functioning or the water appearing isn't hot sufficient, you might require to check the temperature level setups on your upper thermostat. Make certain the breaker is switched off prior to doing anything. Open up the access panel and press the red switch for temperature reset above the thermostat. This must aid heat the water. Turn the breaker back on and inspect if the trouble has been settled.

Call A Specialist:


If after replacing all damaged parts and resetting your temperature level, the hot water heater still isn't functioning, you may require to speak to an expert plumber for a professional viewpoint. The issue with your heating system could be that the hot and cold taps have actually been switched or it may be undersized for the amount of hot water needed in your home. Whatever the case may be, an expert plumber would assist solve the trouble.

Final thought


Hot water heater issues are not constantly major. Many of them are because of minor issues like a blown fuse or worn-out burner. Replacing the damaged components must suffice. Nonetheless, if you are still not able to resolve the trouble, give a call to your closest plumber to come to get it repaired.

8 possible reasons why you have no Hot Water


Along with streaming Netflix and having light flood a room when we flick a switch, having hot water flow from our taps and showerheads whenever we want is an oft-overlooked modern miracle of homeownership. That's why, when that flow goes cold, it can be shocking — and not just in a "Wow, that's freezing" kind of way while you're in the shower.


Water Leak


Before hot water reaches your taps and showerheads, it needs to spend some time in your water heater. This appliance, which can be either gas- or electric-powered, takes the cold water that enters your home from your well or utility company and cooks it until it gets hot. It's akin to an electric tea kettle.



Obviously, if your water heater is leaking, it will never fill with water so it won't have anything to warm. To see if this is the case, simply examine the area around the water heater to see if it is wet. If so, you'll likely need to replace the unit, but you can also call in a pro for a second opinion and to see if it is fixable. Sometimes leaks can happen around fixtures on the water heater, and if so, the solution might be as simple as replacing them.


Gas Heater: Gas Leak


If your hot water is fueled by natural gas and there is a leak in the supply line or where the line enters the tank, the appliance won't have the power it needs to heat up your water. The result is not only inconvenient, but it can be extremely dangerous as well. If you smell gas when you investigate your water heater, call your gas utility company immediately and report it as an emergency. It might also be prudent to leave your home until a repair person from the company arrives. Your utility company will usually fix any kind of gas leak. However, in terms of getting your water heater working again, you'll need to relight the pilot and wait a while to see if it is functioning properly. You can call in a water heater specialist or plumber to help with this.


Gas Heater: Pilot Light Problems


There are two other issues with gas-powered water heaters that can lead to a loss of hot water. The first is a pilot light that's blown out. The pilot light is the source of a constant flame inside your water heater. When the heater determines the need to heat up the water it is holding, it will open a valve that will cause gas to flow over the pilot light and cause it to ignite. To see if your pilot light is functioning, there is usually a small window in the front of the water heater. If you can't see a flame, remove the access panel and see if that helps you locate it. If there is still no flame, you'll need to relight it in accordance with the manufacturer's instructions.



Your pilot light should burn with a bright blue flame. If not, make sure there are no drafts affecting it, which could keep it from functioning properly. If the flame looks yellow, it might be a sign of the presence of carbon monoxide, which spells trouble and needs to be looked at right away by a technician.


Gas Heater: Faulty Thermocouple


The second reason why a gas-powered water heater might fail is a faulty thermocouple. This is a small probe that should sit in the pilot light flame. Its purpose is to stop the flow of gas if it senses that the pilot light is out. Sometimes, these probes get knocked off track, so make sure it is directly in the flame. They can also get a buildup on them that prevents their function, so try cleaning yours off with some steel wool or fine-grit sandpaper. If your pilot light won't stay lit and you've tried these steps to fix the thermocouple, it is likely faulty and needs to be replaced. Call a technician.


Electric Heater: Breaker Blues


Electric water heaters don't have pilot lights, because there is no gas to burn in order to heat up the water. Instead, they do their magic through the use of (naturally) electricity. But that's not to say things can't go wrong with them. If your electric water heater isn't working properly, there's a good chance that a breaker was tripped that supplies the appliance power. Check your breaker box and flip any breakers that have switched to the off position back on. If it trips again, then there might be a fault in the water heater, and you'll want to call in a pro to have a look.


Electric Heater: Reaching The Limit


If the breaker is fine, check to see if the high-temperature limit has switched off on the water heater itself. To do so, first turn off the breaker to the unit. Then remove the service panel and press the red button you'll find there. This is the limit switch, and resetting it could solve your problem. To check, replace the panel, turn the breaker back on and listen to see if the water heater is functioning again.


Electric Heater: Heating Element


If these steps don't fix the issue, then you might have a failed heating element, which will need to be replaced. Unless you are comfortable with such repairs, calling in a technician might make the most sense.

https://www.homeserve.com/en-us/blog/home-improvement/no-water-heater/



As a serious person who reads on What Would Cause My Electric Water Heater to Stop Working?, I was thinking sharing that excerpt was a great idea. In case you liked our post kindly remember to share it. Thank you for taking the time to read it.


Book Your Appointment

Report this page